Tongcheng Machinery Co., Ltd.
Service Hotline:13637166582
Banner
NewsYou are here: Home > News > Content
Air Oblique groove Construction
Edit:Tongcheng Machinery Co., Ltd.   UpDate:2018-12-24

We all know that cement is a universal material in building buildings, but how is it produced, and what tools are used in its production process? Today, in order to answer the above questions, the small editor specially selected the modern cement production indispensable tool-Air Oblique groove, and it is used as the object of discussion. You can take a look at the following introduction, what questions can go to the company's official website to inquire!

Air Conveying slant GrooveComposed of the following components: Standard Groove (the main component of the slant, its length is 3 meters), non-standard groove (used to meet less than 3 meters in the process layout size, usually take a multiple of 250mm), Feed slip pipe: (In order to reduce the local wear of the breathable layer under the feed port, In the installation of the site can be in accordance with the secret master map of the feed pipe position and feed slip board construction drawings in the size of the drilling fixed), 90 degree bend groove (conveyor line transfer 90 degrees, divided left and right to two species), three-way groove (in the conveyor line redirection with the left direction and directional two species) four-way groove (divided into three out, three into one out of two), The truncated valve (when the portion of the oblique groove is deactivated, the corresponding valve can be closed to ensure that the material is inflated with air volume or less extension to reduce consumption) and Peep window (for observation of material flow). Generally located in the inlet after the 2~3 meter in the mouth of the bend groove, three-way groove, four-pass groove in front. On-site installation can be in accordance with the requirements of the general map, welding in the general diagram of the installation requirements, welding in the upper shell easy to observe the side. ), Groove frame (generally set up a groove rack every 4 meters slant groove, be careful not to be too close to the Groove interface flange), the end cover (for the high-end sealing plugging plate of the slant Groove), the discharge pipe (used for discharging port discharge), the breathable layer (used to provide the conveying material, at the same time can make the compressed air evenly through it to "inflate" the material, so that the material fluidization. Its material is used in a variety of applications, the user can customize according to the use of the Groove vent (exhaust volume According to the required component of 1.5 times times to consider. Normal operation, its upper groove pressure requirements to maintain around 0 pressure), fan options (fan air volume, full pressure, power, speed, etc. according to the calculation results determined. Usually equipped with type 9 to 19 centrifugal extension. Existing XQI, xqii type oblique groove high-pressure fan, its flow and full pressure for the air transport slant can be a good match, the price is relatively high, recommended preferred selection)

Conveyor slant material status for dry powdery or granular through the 3~6mm below easy to inflate powder particles, surface moisture can be around 0.8%, otherwise it will cause stasis, or even blockage. Conveying capacity: The conveyor volume of the slant is affected by more factors, which often vary greatly. The slant groove is different from other conveying machinery, the conveying quantity is too low, often can not carry the material smoothly. On the contrary, the appropriate increase in the muscular layer can improve the material gasification uniformity, but should pay attention to keep the thickness of the material layer as the height of the channel (upper shell) around the 1/4~1/3, pay attention to the selection of the appropriate groove width according to the productivity. Excessive thickness of the material layer will have an adverse effect on the conveyor.

Due to airConveying Slant GrooveIn the conveyor material does not drive the parts with its function of the belt conveyor, screw conveyor, buried scraper conveyor compared with less wear, easy to maintain, less power consumption, wood, no noise, good sealing, simple construction, safe and reliable operation, at the same time easy to change the direction of transportation and multi-point feeding, unloading and other advantages. As a result, it has been adopted by many enterprises in recent years.

  The above is aboutAirInclined GrooveThe details of the use, hope to give you in the construction engineering and other academic to bring help. If there is a need for shopping in the conveyor slant, you are welcome to call the majority of users to inquire about ordering! The company has been pursuing a professional development path, through continuous improvement, always master the high-end precision of the core technology, superb manufacturing technology and product quality control, with our professional services to help customers create higher value, we believe that through our continuous efforts and pursuit, will be able to achieve mutual benefit with customers and win!

 

 

Mobile